 | Free Engraving Software |
| These programs are made by ourself and may not copied or distributed for commercial use and not use for comercial engraving , you can download it and use it for free. When you download a program please send me an Email with your name and E-mail adress, so i can send you a message when there is something wrong with the program or we have an update. Here it is. The newest Software. This is an Beta version for testing. Make a Directory c:\majosoft and place this file
( 220 kb ) and run it. When he ask something answer with "y" ( yes ) |
| | | | ( Do NOT Use option for H-bridge ) |
|
| | | This program CAN run under windows(95,98,ME) in a DOS box. This is no problem, you must set the CVE low. |
| XT with an VGA screen and DOS 3.3 or higher. |
| LAST UPDATE 11 - Sep - 2000. |
| If you have a problem with reading G-Codes please send the G-Code to me and i try to fix it.
If you use an other G-Code send it to me and mayby i can change my program so you can use it. If you have suggestions about the program say it to me. |
| You can use this program for : |
| *Conrad steering card smc800 and smc1500 |
| *Your own steering card with ULN 2803 or ULN 2003, with or without an inverter on the card. |
| *An Engravingmachine 3D |
| *An Plotter. ( if you use your own steering card then you can use 4 pens ) |
| You can use 2 kind of file types : |
| *HPGL files with extension .PLT |
| *G-CODE files with extension .DIN The following G-CODES are availeble : |
| *G0, G1, G2 with I,J,K as circle centre |
| *G55 Shifting Zero point X, Y, Z, W ( this is the rotating angle ) Increment |
| *G56 Shifting Zero point X, Y, Z, W ( this is the rotating angle ) Absolute |
| *G58 Mirror X, Y, Z on particular X and Y coordinaat |
| *G59 Stretching X, Y, Z |
| *G90 ( absolute ) and G91 ( increment ) you can use this in 1 line. |
| *Example : N1 G2 G90 X10 Y10 G91 I5 J5 G90 ( the circle centre is increment but the end coordinates are absolute ) |
| *You can use line numbers, but it is not nessesary.( NOT YET , see expected in next version ) |
| *You can use Y but also y. It doesn't matter. |
| Options in the Software : |
*Rotating the PLT file with 3 dec after the point. |
| *Miror PLT file in X and Y |
| *Several times to depth with PLT file. |
| *You can choose witch pen you want to draw . Only PLT Files. ( 0 = pen in program ) |
| *You can give the distance between the pens. |
| *G-Code or Plt files |
| *Conrad or your own steering card. |
| *Lpt1, Lpt2 or Lpt3 |
| *Stretching X, Y or Z |
| *Zoom function |
| *Step by step engraving |
| *If your cutter is broken, you can start halfway. Only PLT files. |
| *During Engraving of an PLT File, you can press D. ( The cutter goes 0.1 mm down )
or you can press U. ( The cutter goes 0.1mm up ) |
| *Preset X, Y and Z ax.
Example : You move the cutter to an position and then you can say X = -12.234 |
| *You can move Zero to the Upper Left or Lower Left Corner. ( only PLT file ) |
| *Steps / mm for each ax. Positive or Negative. |
| *Two languages. ( Dutch and English ) |
| *Show all end points |
| I have also write a program to convert a fotoscan to 3D G-Code or 3D-HPGL file. ( the name of the file who made is something.din ) I hope you try this software and say me if its wrong. This file is a selfextracter, after you run it, run setup.
The y-. and z.234 fault and the lines who doesn't matter are out.
( i hope you understand what i mean. ) |
| | | | | I try to make an NEW program for this because many people had to many questions about this program. |
|
| | | | | | | plt-engels.zip( 135 kb ) | | | | Old Software | | | Latest version : 01 mei 2000 | | | Software for the Conrad steeringcard smc800 and the smc1500 | | |
| |
| |
